让你的魔方没这么容易pop(散架)

gan

今天逛了逛http://www.planet-puzzle.com/

进入FAQ看到这文章

難・op 加工について　/ About difficult Pop processing

大意是加工你的魔方,使它没这么容易散架

但具体没弄懂,感觉是加橡胶圈进入螺丝(铆钉)的旁边,是这样吗?有谁弄懂的跟帖说说吧

老猫

*"Difficulty Pop processing" is a processing not made Pop easy to do. (It is the state as it is. ^^;) Often..turn..cube..inside..polish..decrease..cube..space..
grow.The new article is Shiccari and a cause of the return of this and rotating heavily in a central cube as for other cubes though there is so not doing Pop because it suppresses it. Accident Pop processing by the thing is effective in "
New cube that adjusts the center" and "Cube for in season to have approached the end". So as not to make Pop easy to do in the cube that becomes superannuated, driving a central bolt is thought. "Drive of a central bolt" becomes very slight work. It is a thing that it is easy to bend in a central bolt when the first of all difficult one is driven. It is large ..another.. and, moreover, the bolt of Me is necessary to drive it straight. After that, a large nut that supports a medium vise and the space that fixes parts around the center is needed. So as not to drive the hammer too much, it slowly drives it in with. (The bolt doesn'
t enter if power is not put in the small one. )
There is a space of 1mm or less in the inside where the part of the umbrella of a central bolt and Fta of a central cube were opened. (Without the mistake because it is not between central Paul and central cube. )The cube comes for Pop not to do easily by reducing this space. However, it becomes finished of eyes with a firm rotation because it increases considerably only by inputting the pressure in spring a little at the same time. *I in the translation am dealing by putting the one like O ring (Orring) in this space. It was too caught and not good first though had put a metallic washer. After all, the one on the market was Imaiti with this because it was too thick though the above-mentioned O ring was bought and shown afterwards. (thing of 1mm exaggerated thickness)Another one is being put now though it is various. First of all, the rubber seat of 0.5mm thickness is bought. (About 400 yen by one rolling. )The one that it was thinner and the size is smaller was not sold though was acceptable either. After that, two kinds of sizes have been bought by the one "High-level skin punch". It is the one of the diameter 3mm and 12mm. (400 yen or less both)You may suitably cut outer with scissors. The rubber seat is clipped to "Doughnut" with these two punches. It is made to narrow the space between a central bolt of a ready doughnut and and a central cube.
It is this and Battiri. (^^) When it was this method, it hardly changed, and the pressure in spring was able to leave the cushion reduced the space under such a condition, and kept a little in addition. There is so trying not to drive of a central bolt needing either. ()Because the cost is cheap, it only has to exchange it though there is how much durability of rubber now. It is a little troublesome though thinks it is very epoch-making for myself even if it is said that it will cover with the doughnut. Tweezers are necessaries. However, I think that it manages to become it. (^^) The center is adjusted with a tool of outside the center and after the rotation is lightened a little, and a new cube are accustomed to Oshaca one new cube my variously doing with. (The grinding medicine is put and it is various. )The accustoming period shortened greatly by this. If the center is adjusted, it is FSC Houdai from the first day though is still caught because it is a new article of course. (^^) ･The cube embezzled now puts and deals with the rubber doughnut. The center is not adjusted. It is too slight though the nature that wants to be input only just a little is done in reality. When I become a turn of the rotation in each respect in the Hobo nonresistance it, (^^; I am transferring to the following new cube. Embezzling as it is and becoming superannuated are wasteful. The turn has been reduced around of "In season". The cube when the layer method is started doesn't become something useful so much in the measurement Hirahe because it has embezzled by doing. (Exchanged it in reinforced spring. )It transfers sequentially from the cube afterwards. It is transferring newly recently. Being practicing is a new cube of the adjustment of here, and the previous "In season" cube of one for the real thing such as rallies. However, reaching a new high always is a cube in rotate heavy, new one. ..amusement... (^^;

[此贴子已经被作者于2006-3-9 17:35:20编辑过]

新手007

no

conancliff

这是什么原理啊？

没看懂

94Walter

作者将其戏称为“橡胶炸面圈”。

和国产DIY（很感谢，已收到）的大型调整垫圈是一个作用。适用于使用了一定阶段的魔方。缩短弹簧伸展幅度的同时降低了金属物长期摩擦中心块造成的老化现象。买了一定厚度的胶皮后用两种规格的皮带冲子简单搞定。

至于其中所提到的“阶段”，和原先打磨主题里面的是同一个词。和这个神经质（作者的一贯作风）的话题一样是个主观上的概念。如果是多魔方长时间练习的高级魔方爱好者，通过观察结构，以及手感方面的体会可能有自己的见解。

至于如何拔除柳钉，日本人用的是小钳子。（cube_master专用的用起来会顺利许多吧）

虽说先天具备优越的弹性，但橡胶的磨损速度不能不考虑。一来二去再次体现了作者自负（这点他本人还是自知的…）的玩家精神。

—————————

于是本主题可能又引出了国产DIY的另一个优点。中号、大号垫圈粗糙面重合后把光面留给了塑料和螺丝，降低转动阻力的同时保护了部件。

fengyu0523

完全看不懂：（

皮莨鲤厶

.我的魔方也很容易散...  不过大概是手法不对.吧

xiaozhuzy

放哪个地方啊 ??图不详细啊

thief

我的魔方偶尔POP时就像发射一样，一下子就非出去了。

怎么调也不舒服

螺丝紧点就很难转动``可是松点就会不定时“发射火箭”！

恼火啊